Tensys
EX VAT
INC VAT
0 items £0.00
YOUR BASKET

You have no items in your basket

Tag: ratchet-strap-hooks

50mm Ratchet Strap Hooks

Two straps can be the same width and still need very different endfittings to attach safely. The hook is the small detail that decides whether the strap secures properly on your vehicle, follows a sensible line of pull and stays where it belongs while you tension it.

This guide compares familiar hook profiles, then looks at specialist car-transport and tracking fittings. It's intended as a practical selection guide, not a restraint calculation or a technical design instruction. Always check the actual strap, fitting and vehicle guidance before use.

 

PICTURED ABOVE (LEFT TO RIGHT):
Claw Hook // Combi Hook // Open Rave Hook

PICTURED ABOVE (LEFT TO RIGHT):
Closed Rave Hook // Flat Snap Hook // Twisted Snap Hook

 

Start with the anchorage, not the hook name

A hook must match an approved load-securing point, not simply something it can catch around. A sound connection on one trailer may be unsuitable on the next. DVSA guidance calls for adequate strength, compatibility and minimal movement without distortion. [1]

The fitting should bear where its manufacturer intends, with the pull in the permitted direction, rather than balancing on its tip or being levered sideways. Always ensure that the anchor point used fits into the base radius of the hook with clearance – never force the hook onto too large a diameter of anchor, as this may cause premature failure. See our previous blog post Choosing the Correct Hook Size for more information on this topic.

 

50mm is a width, not a capacity

The width describes the webbing, not the load you can safely carry. Read the complete assembly's legible label, including its BS EN 12195-2 identification and the ratings that are relevant to your restraint method. If you're not sure how to read the product label, see our previous blog post Ratchet Strap Labels: What Do All the Different Terms Mean?

Lashing capacity (LC) is a force used for direct-lashing calculations. Standard tension force (STF) describes the tension produced under standard conditions and is relevant to frictional tie-down restraint, the force that the tensioned strap applies to the load. Breaking strength BFmin is a failure measure, not a working limit or a way to choose the number of straps. [1]

Do not treat kilograms of cargo as interchangeable with daN of force, or infer a safe cargo weight from a hook's sales description. The complete assembly and its anchorage are only as strong as their weakest component. Load arrangement, friction, angles and other restraint measures still matter; a stronger-looking hook does not remove that assessment. [1]

 

Meet the eight hook types

Claw / double J

A familiar general-purpose profile

A double-finger J fitting, commonly known as a claw hook, is offered for 50mm webbing in commercial vehicle load securing. Its job is to connect the strap to a compatible approved anchorage, such as a suitably sized lashing ring or side rave on a trailer or goods vehicle. For palletised freight, this can be a straightforward choice when the ring lets the hook seat fully and the intended pull stays aligned. It is not a promise of fit on every ring: reject a connection that traps only the tips, wedges the hook or loads one side awkwardly. Claw hooks are often used to connect to the main chassis of the trailer or the goods vehicle too.

Buy 50mm Claw Hook

 


 

Single pole claw hook

A similar style to the common claw hook, J-shaped but formed from a single wire rod

An alternative to double J claw hooks, ideal for situations where access is restricted and a smaller tip diameter is required. A typical 5000daN (kg) double J claw hook measures 23mm across the tip, whereas the single version is 15mm.

Buy 50mm Single Claw Hook

 


 

Flat J / flat hook

A broader bearing profile

This plate-like profile differs from the round-wire claw. Consider using this hook type in situations where the vehicle maker approves a matching rail or anchorage profile, for example on a flatbed carrying building materials. Its broad appearance does not make an arbitrary bodywork edge a load-securing point. Check the opening, seating depth and intended bearing face against the actual anchor. Thin sheet metal, an unsuitable lip or an edge that prevents full engagement is a reason to choose another approved connection, not to force this one on. This design of combi flat hook will fit the commonly-fitted side rave drop in lashing rings that are TT shaped.

Buy 50mm Flat Hook

 


 

Open rave / chassis

For a matching vehicle profile

A 50mm wire rave hook fitting is intended for suitable vehicle side-rave or chassis attachment. It can therefore suit general freight on a trailer whose approved securing arrangement uses that profile, rather than a lashing ring. The key word is 'suitable': the visible chassis is not automatically an anchorage. Check that the hook seats securely and squarely without distortion and is approved for the pull you need. With an open profile, pay particular attention to whether it can disengage while the strap is slack during fitting.

Buy 50mm Rave Hook

 


 

Closed rave / chassis

Closed does not mean locking

Open and closed rave profiles are available. A closed wire form is not a spring-locking hook; it doesn't have a locking function, the word 'closed' just describes how the shape of the hook is formed. Select it for a compatible approved side-rave or chassis point, such as a trailer arrangement specified for that fitting. Do not assume its name guarantees retention on every anchor, or that it will engage an anchor which takes the open version. One side of the hook will have a gap where the two sides of the wire road are formed together; this may be welded or left with the 2 sides close together. Webbing should never be fitted to this side of the hook as it's not load bearing in this direction of pull.

Buy 50mm Closed Rave Hook

 


 

Flat snap

A catch for retention

A flat snap fitting uses a spring catch across its opening. Consider it where a compatible lashing ring is approved and keeping the connection in place while positioning the strap is useful, for example when securing trade equipment in a goods vehicle or as a crane securing strap on a builders merchant vehicle. The ring must sit inside the hook's intended bearing area and let the catch close fully. The latch is a retention feature; it is not designed to bear a load. If the anchor presses on the catch or holds it open, the connection is wrong, regardless of how firmly the ratchet is tightened. Never use a hook where the catch is missing or damaged.

Buy 50mm Flat Snap Hook

 


 

Twisted snap

A different webbing orientation

Twisted snap fittings also have a spring catch, but offer a different orientation from the flat version. Where approved for use, this geometry may suit a ring and webbing route that would otherwise leave the strap poorly aligned, for example on a vehicle with differently oriented anchorage rings. This is a selection consideration, not permission to twist the webbing to make it fit. A twisted snap hook is not a swivel. Check the actual product drawing and permitted pull direction; neither the catch nor the twist makes side-loading good practice.

Buy 50mm Twisted Snap Hook

 


 

Claw hook with safety catch

Shape and retention are separate choices

Spring-catch claw variants also exist. So 'claw' describes a profile as in the wire-formed J shape described above, while 'snap' describes a retention feature which is normally a spring loaded catch; a fitting may combine both. Ask for the exact part or assembly reference rather than relying on a name or photograph alone. Refer to the dimensional drawings for the endfitting when making an informed choice. Claw hooks with safety catches come in several sizes to suit different diameters; there are versions to suit up to 15mm, 24mm and 30mm Ø bars or lashing points. The larger 30mm version is commonly used to connect to the lashing bars on container flat racks.

Buy 50mm Claw Hook with Safety Catch for 15mm Bar Buy 50mm Claw Hook with Safety Catch for 30mm Bar

 

Specialist fittings are a different conversation

For car transport, identify the complete approved wheel-restraint system and its specified deck connection (e.g whether punched decking or ring type lashing points). A single swivel fitting is not a generic replacement for a claw hook; its mating aperture, engagement and permitted orientation must match the transport system. On multi-car transporters, the hook strength is often limited to 3000daN (kg) breaking force because the hook wire diameter is smaller than for 5000daN(kg) hooks to allow fitting into the punched decking.

For securing roll cages and other loads within box vans, a tracking fitting must match the particular load-restraint track and its rating, not merely slot into a convenient opening. Care has to be taken not to damage the load, tracking or the vehicle/trailer side walls.

Do not mix fittings between tracking families or assume that all perforated decks accept the same connector. If the equipment needs a specialist connection, buy the specified assembly.

 

A practical choice checklist

Before ordering or fitting a strap, work through these checks. The application examples above are conditional starting points, not approval for a particular vehicle or load.

  • Identify the approved anchorage and confirm its strength, dimensions and permitted load directions with the vehicle or equipment supplier.

  • Match the exact hook profile and opening to that point. Check full seating, clearance and any catch operation before tensioning.

  • Choose the complete labelled assembly for the restraint method. Check LC and, where relevant, STF; do not select by webbing width or breaking-strength headlines alone.

  • Check the webbing route. Avoid twists, sharp or abrasive contact and any hook position that creates tip-loading, side-loading or leverage.

  • Inspect the webbing, stitching, ratchet, hooks and anchorage before use. Remove damaged equipment from service and use suitable edge protection such as sleeves or plastic corner protectors.

  • Confirm the load-securing plan, not just the connection. If fit, rating or the required restraint is uncertain, stop and obtain competent advice.

 

Habits that matter whichever hook you choose

Never use sheeting or rope hooks as load-securing anchorages. The triangle shape formed by the 2 sides of the claw hook closed together should never be placed over a rope hook as the hook is not load bearing at this point (the weld at this point is to retain the shape of the hook during the heat treatment and corrosion-plating processes). The DVSA also says not to attach more than one lashing to an anchorage, or thread a lashing through a point and hook it back to itself. Inspect before use, protect webbing from sharp or abrasive edges, and replace damaged webbing or end fittings rather than carrying on with a strap that is not in good condition. [1]

Ratchet lashings are for securing loads, never for lifting. A catch that sticks, a distorted hook, damaged stitching or an unreadable label deserves attention before the next job, not after it. A replacement fitting should be approved as part of the assembly; do not improvise a repair because the replacement happens to accept 50mm webbing.

 

The right hook is the one that genuinely fits

There is no single best hook for every 50mm strap. Start with the approved anchorage, choose the profile and retention arrangement that works with it, then check the whole assembly and restraint plan. A well-matched connection is more useful than an impressive-looking hook or a bigger number in a product headline.

 

Sources and editorial notes

DVSA provides the overarching safety guidance. Manufacturer pages identify example fitting types, not universal compatibility or ratings. Application suggestions are editorial guidance subject to product and vehicle approval. Figures in source titles are retained verbatim and are not ratings for every 50mm strap.

[1] DVSA – Securing loads on HGVs and goods vehicles: 4. Ways to secure a load in an HGV or goods vehicle. Updated 24 September 2026.

Buy Endfittings from Tensys Direct